Electrolux Appliance Repair & Error Code Lookup
Find your Electrolux error code below, see what it means, and know whether it's safe to clear yourself or time to call a certified technician.
Electrolux Washing Machine — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| E20 / E21 |
Drain Line Blocked / Drain Pump Fault
Water failed to empty from the tub within the designated time. Check filter trap, drain hose, or replace drain pump.
|
High |
| E10 / E11 |
Water Inlet Fill Failure
Washer taking too long to fill or no water stream detected. Check home supply valves and inlet valve filter screens.
|
Medium |
| E40 / E41 |
Door Latch switch Open
Door assembly open or door lock mechanism failed to lock before cycle start.
|
Medium |
| E5E / E51 |
Motor Drive Board / Inverter Fault
Communication loss or power triac failure between main control board and drum drive motor inverter module.
|
High |
| E31 / E35 |
Pressure Switch / Overfill Signal
Electronic pressure sensor reading out of calibration or overfill switch triggered due to excessive foam or water level.
|
High |
Electrolux LuxCare® front-load washers often display "E20" when the front cleanout filter becomes clogged with small objects or lint. Always drain manually and check the coin trap before replacing the drain pump.
Signs your Electrolux washing machine needs a professional
- Washer stopping mid-cycle full of water with door remaining tightly locked
- Grinding or loud squealing noise during spin cycle (spin bearing or tub spider arm damage)
- Error codes starting with "E5" returning immediately after a hard power reset
- Water leaking out from underneath the front door gasket or dispenser drawer
Electrolux Dryer — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| E61 / E64 |
Heater Circuit / Thermal Cut-Off Open
Dryer heating element relay open or thermal fuse tripped due to overheating or restricted exhaust airflow.
|
High |
| E31 / E32 |
Moisture Sensor Error
Conductive moisture sensing bars reading out of frequency range or disconnected from control board wiring.
|
Low |
| E42 / E5B |
Control Board Communication Loss
User interface board unable to communicate with main electronic power module inside rear cabinet.
|
High |
| E91 / E9E |
UI Touchpad Communication Error
Software mismatch or short circuit within front control panel touch pad membrane.
|
Medium |
If your Electrolux dryer runs without heating and shows an "E64" code, check the external exhaust duct. A clogged exhaust line causes internal temperatures to spike, blowing the non-resettable thermal limit safety switch.
Signs your Electrolux dryer needs a professional
- Dryer running continuously without producing heat or drying clothes
- Loud thumping or squeaking noise during drum rotation (roller or idler pulley wear)
- Display shutting off mid-cycle or throwing "E91" code repeatedly
- Dryer cabinet feels excessively hot to the touch during operation
Electrolux Refrigerator & Freezer — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| OP / SH |
Thermistor Open / Shorted
Temperature thermistor sensor circuit in fresh food or freezer compartment has failed or disconnected.
|
Medium |
| SY CE |
System Communication Error
Communication failure between user interface board and main power control board.
|
High |
| SY EF |
Evaporator Fan Circuit Failure
Evaporator fan motor running out of speed tolerance or fan blade frozen in ice buildup.
|
High |
| SY CF |
Condenser Fan Circuit Failure
Condenser fan motor not receiving signal or seized. Compressor may overheat and shut down.
|
High |
| DF |
Defrost Circuit Error
Defrost heater or thermostat failed to clear evaporator coil frost within max cycle window.
|
Medium |
The "SY EF" code on Electrolux French Door models often indicates that ice has accumulated around the evaporator fan housing in the freezer, preventing the blade from spinning freely. A full manual defrost may temporarily restore function while diagnosing the defrost drain.
Signs your Electrolux refrigerator needs a professional
- Fresh food section warm while freezer section is freezing properly
- Blinking error code "SY CE" or "SY EF" displayed on front door control panel
- Ice maker completely stopped producing ice or leaking into ice bin
- Clicking sound coming from bottom rear compressor area every few minutes
Electrolux Dishwasher — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| i10 / i11 |
Water Fill Timeout
Dishwasher failed to fill with water within designated time. Inspect supply valve under sink or inlet valve.
|
Medium |
| i20 / i21 |
Drain Fault
Water remained in bottom tub after drain cycle. Check for clogged fine filters, garbage disposal knockout, or pump blockage.
|
High |
| i30 |
Aqua Control / Anti-Flood Activated
Water detected in bottom pan under dishwasher tub. Float switch tripped; drain pump runs automatically.
|
High |
| i50 / i51 |
Wash Motor Circuit Fault
Circulation pump motor short circuit, triac failure, or tachometer signal loss on control module.
|
High |
| i60 / i61 |
Heating System Fault
Water temperature failed to rise during wash cycle. Heating element coil or NTC sensor issue.
|
Medium |
An "i30" code on Electrolux dishwashers triggers an immediate drain pump response and turns off control panel input. This means water has leaked into the lower overflow tray. Unplugging the unit and addressing the source of the leak (door seal, spray arm split, or tub hose) is required before resetting.
Signs your Electrolux dishwasher needs a professional
- Drain pump running continuously even when door is open or power is turned off
- Error code "i30" or "i50" showing on top edge door display
- Dishes coming out cold and wet with soap detergent tablet un-dissolved
- Water pooling in bottom tub after cycle finishes
Electrolux Oven & Range — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| F10 / F11 |
Control Board / Microprocessor Fault
Internal memory error on electronic oven control (EOC) board or stuck touch panel key.
|
High |
| F30 / F31 |
Oven Temperature Sensor (RTD) Fault
Temperature probe sensor circuit open or shorted. Oven cannot detect internal temperature accurately.
|
Medium |
| F90 / F91 |
Door Lock Mechanism Fault
Motorized door lock assembly failed to engage or unlock during clean/cook cycle.
|
Medium |
| F40 |
Cooktop Communication Error
Communication signal lost between induction or electric cooktop controller and main display.
|
High |
On Electrolux induction ranges and wall ovens, "F10" or keypad fault codes often occur after high-heat self-clean cycles. The excessive thermal buildup can damage top control relays or thermal fuses mounted above the cavity.
Signs your Electrolux oven or range needs a professional
- Oven door remaining locked shut after self-clean cycle ends
- Bake or broil elements not heating despite display showing target temperature
- Continuous alarm sounding with "F10" or "F30" code on screen
- Induction cooktop burner zones flashing error code and refusing to heat cookware
Electrolux Repair FAQ
How do I reset error codes on my Electrolux appliance?
You can perform a hard power reset by switching off the circuit breaker for 10 minutes at your main home breaker panel (or unplugging the unit). Turn the breaker back on to clear soft memory errors. If an active hardware fault exists, the error code will re-appear.
Why is my Electrolux washer displaying E20?
The E20 code indicates a drain fault. Inspect the lower front drain pump filter trap for debris like lint, coins, or small garments. Ensure the drain hose behind the washer isn't kinked or blocked.
What should I do if my Electrolux dishwasher shows code i30?
The i30 error means the anti-flood float sensor in the base pan detected water. Immediately turn off the water valve to the dishwasher and switch off power at the breaker to prevent overflow before calling for repair.
Are genuine Electrolux factory OEM parts used for repairs?
Yes, all Electrolux appliance repairs are completed using genuine OEM factory replacement parts to restore factory performance, efficiency, and reliability.
Still seeing the error?
Our technicians diagnose and repair Electrolux premium washers, dryers, fridges, and cooking appliances daily. Get it fixed right the first time.