GE Monogram Appliance Repair & Error Code Lookup
Find your GE Monogram error code below, see what it means, and know whether it's safe to clear yourself or time to call a certified technician.
GE Monogram Built-In Refrigerator — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| HRS |
Defrost System Failure
Main control board detected defrost heater open circuit or thermistor error. Unit stuck in defrost mode.
|
High |
| CC |
Freezer Temperature Too Warm
Freezer cabinet temperature has been above normal setpoint for over 2 hours. Inspect door seal and condenser coils.
|
High |
| CI |
Ice Maker System Error
Ice maker mold or rake motor jammed, or water fill cycle failed to complete within timed window.
|
Low |
| DE |
Defrost System Circuit Error
Evaporator temperature did not rise during defrost heater cycle. Potential heater or defrost thermostat failure.
|
Medium |
| PF |
Power Failure Alert
Electrical supply to unit was interrupted. Press System Check or Alarm Reset button to clear display code.
|
Low |
Built-in GE Monogram refrigerators feature top-access condenser coils behind the flip-up machine grille. An illuminated "CC" or warning alarm is frequently caused by blanket dust buildup restricting airflow across the overhead condenser matrix.
Signs your GE Monogram refrigerator needs a professional
- Code "HRS" displayed on internal digital screen with compressor not running
- Fresh food compartment warm while freezer frost accumulates on back panel
- Ice maker completely stopped or dispenser flapper door leaking cold air
- Repetitive clicking sound from top sealed system inverter board
GE Monogram Oven & Professional Range — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| F2 / F20 |
Oven Over-Temperature Condition
Cavity temperature exceeded safe maximum limit (over 630°F in bake mode). Relay contacts stuck closed or RTD sensor failed.
|
High |
| F3 / F30 |
Open Oven Temperature Sensor (RTD)
RTD temperature sensor circuit open or disconnected. Control cannot measure internal cavity temperature.
|
Medium |
| F4 / F40 |
Shorted Oven Temperature Sensor (RTD)
RTD probe harness shorted to ground or probe resistor failed internally.
|
Medium |
| F90 / F96 |
Motorized Door Latch Fault
Door lock motor or latch limit switch failed during self-clean lock or unlock sequence.
|
High |
| F70 / F76 |
Touch Panel / UI Board Failure
Keypad membrane shorted or communication loss between glass touch panel and oven control board.
|
High |
GE Monogram gas professional ranges feature dual-ring brass burners and heavy-duty igniter modules. If range top igniters click constantly, check that the brass burner ports are free of boiled-over liquids and that burner caps are seated completely flat.
Signs your GE Monogram oven or range needs a professional
- Oven door remaining locked shut after self-clean cycle ends
- Continuous alert chime with "F2" or "F90" error code on control panel
- Bake or broil elements not heating despite display showing active preheat
- Gas oven igniter glowing orange/red without lighting gas burner within 60 seconds
GE Monogram Dishwasher — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| FTD / H2O |
Failure to Drain
Water remaining in tub after drain cycle. Check sump filter mesh, garbage disposal knockout, or drain pump motor.
|
High |
| FTF |
Failure to Fill
Dishwasher failed to reach required water level in allocated time. Water inlet valve or pressure switch issue.
|
Medium |
| C1 / C2 |
Drain Line / Pump Time Out
Drain pump ran longer than expected without pressure switch resetting to empty state.
|
Medium |
| C8 |
Detergent Cup Blocked
Detergent dispenser door jammed by oversized dishware or actuator spring switch defect.
|
Low |
GE Monogram dishwashers use an active floor pan float sensor. If the control panel flashes "FTD" or "H2O" while the pump runs continuously, inspect the lower door gasket and tub corners for minor water seepage.
Signs your GE Monogram dishwasher needs a professional
- Drain pump running non-stop with door open or power button switched off
- Dishes coming out cold and wet with detergent cup un-opened
- Display locked on "FTD" or "FTF" despite clearing tub filters
- Water pooling under bottom rack after cycle ends
GE Monogram Washing Machine — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| E22 / E23 |
Water Fill Time Out
Washer took too long to fill with water. Check home shutoff valves and inlet valve screen filters.
|
Medium |
| E30 / E31 |
Drain Pump Time Out
Water failed to clear tub within allocated time. Inspect coin trap filter and drain hose for blockages.
|
High |
| E60 / E61 |
Door Lock Circuit Failure
Door lock switch failed to engage or register locked state with main control module before spin.
|
Medium |
| E70 / E71 |
Motor Drive Board Error
Inverter motor board error or loss of tachometer speed feedback from direct drive motor.
|
High |
If your washer displays "E30", drain water manually via the lower emergency drain hose and unscrew the pump filter cap to clear small objects like coins or lint build-up before replacing parts.
Signs your GE Monogram washing machine needs a professional
- Washer stopping mid-cycle full of water with door locked
- Loud thumping or grinding sound during high-speed spin cycle
- Display locking up with "E70" motor control fault
- Water leaking out from door boot gasket area
GE Monogram Dryer — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| E80 / E81 |
Exhaust / Flow Restriction
Airflow restricted in exhaust duct network or lint screen area causing thermal safety switch trip.
|
High |
| E64 / E65 |
Heater Circuit / Thermistor Fault
Heating element open, thermal fuse tripped, or inlet NTC thermistor reading out of calibration.
|
High |
| E32 |
Moisture Sensor Error
Moisture sensor bars shorted or disconnected from front bulkhead wire harness.
|
Low |
Code "E80" or "E81" indicates high duct backpressure. Clean your home exhaust vent pipe completely; prolonged restriction will blow the internal high-limit thermal safety fuse.
Signs your GE Monogram dryer needs a professional
- Dryer tumbling without producing heat or drying clothes
- Squeaking or heavy thumping noise from drum support rollers
- Dryer cabinet feeling hot to the touch while clothes remain damp
- Unit shutting off mid-cycle with error code on display
GE Monogram Repair FAQ
How do I reset error codes on my GE Monogram appliance?
You can perform a system reset by turning off the dedicated circuit breaker at your home electrical panel for 10 minutes. Turn power back on to clear soft memory errors. Active component failures will re-trigger the error code.
Why is my GE Monogram refrigerator displaying "HRS"?
The "HRS" code indicates a main control board defrost logic failure. The unit is typically stuck in defrost mode and requires board inspection and replacement by a certified technician.
What does error code F2 mean on a GE Monogram oven?
Code F2 indicates an over-temperature condition where cavity temperatures exceeded safe operating limits. This is usually caused by a stuck relay on the power board or a faulty RTD temperature sensor probe.
Are genuine GE Monogram factory OEM parts used for repairs?
Yes, all GE Monogram repairs are completed using genuine OEM factory replacement parts to maintain luxury performance, efficiency, and safety standards.
Still seeing the error?
Our technicians diagnose and repair GE Monogram luxury built-in refrigerators, ranges, ovens, and dishwashers daily. Get it fixed right the first time.