Viking Appliance Repair & Error Code Lookup
Find your Viking error code below, see what it means, and know whether it's safe to wait or time to call a certified technician.
Viking Refrigerator & Freezer — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| HI |
High Temperature Alarm
Cabinet temperature exceeded 60°F. Caused by door left open, failed cooling cycle, or dirty condenser coils preventing heat dissipation.
|
High |
| CL |
Clean Condenser Reminder
Maintenance reminder indicating condenser coils are restricted by dust, pet hair, or grease. Clean coils promptly to prevent compressor thermal overload.
|
Low |
| E1 / E3 |
Fresh Food / Freezer Sensor Fault
E1 indicates a fresh food thermistor error; E3 indicates a freezer thermistor fault. Sensor circuit is open, shorted, or reading out-of-range.
|
Medium |
| E2 / ED |
Defrost System Failure
Defrost cycle failed to heat evaporator coil above required threshold within allotted time. Caused by blown defrost heater, bad bi-metal thermostat, or faulty board.
|
High |
| E5 / E6 |
Condenser Fan or Compressor Fault
E5 flags a stalled condenser fan motor; E6 flags a compressor circuit, inverter board, or start relay malfunction.
|
High |
| oPn / Shr |
Open or Shorted Thermistor
"oPn" indicates an open circuit (broken thermistor wire or failed probe). "Shr" indicates an internal short circuit in a temperature sensor.
|
Medium |
Viking 5 Series and 7 Series built-in refrigerators rely heavily on clean airflow behind the top compressor grille. If you see "CL" on your display, don't ignore it — running a Viking compressor against clogged coils is the primary cause of early inverter board and sealed system failures.
Signs your Viking refrigerator needs a professional
- High-temperature chime sounding continuously even when doors are sealed tight
- Heavy frost accumulation on the back panel blocking freezer air vents
- Clicking sounds every few minutes from the top compressor section (relay thermal trip)
- Water pooling underneath the bottom kick-plate or beneath lower crisper drawers
Viking Oven & Range — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| F10 |
Runaway Temperature Safety Code
Oven cavity temperature exceeded safe operating limits. Typically caused by a welded relay on the control board or runaway heating element.
|
High |
| F02 / F30 |
RTD Temperature Sensor Fault
F02 (or F30/F31 for secondary cavity) indicates an open or shorted RTD sensor probe, preventing accurate cavity heating.
|
Medium |
| F03 |
Cooling Fan Feedback Fault
Control board is not receiving speed feedback from the upper cooling fan. Oven heating is disabled to protect control electronics and cabinet surrounds.
|
High |
| F01 / F07 |
Door Latch or Interlock Switch Fault
F01 flags a motorized door latch circuit failure; F07 flags a door interlock microswitch failure or TruGlide hinge sag alignment issue.
|
Medium |
| F04 |
Shorted Meat Probe Circuit
Internal short in the removable meat probe, or moisture intrusion into the internal wall jack receptacle. Unplug probe to test.
|
Low |
| F06 |
Control Board Configuration Mismatch
Replacement electronic control board installed without matching EEPROM firmware configuration for the specific range model.
|
Medium |
Viking Professional dual-fuel ranges and gas ovens rely on precise high-output spark igniters and high-CFM cooling fans. If code F10 appears, immediately switch off the circuit breaker. A stuck relay can keep heating elements energized continuously even when the oven knob is turned off.
Signs your Viking oven or range needs a professional
- Viking VSH™ or VariSimmer™ surface burners clicking repeatedly without igniting
- Oven door locked shut following a self-cleaning cycle
- Cooling fan making loud screeching or rattling noises behind the control panel
- Uneven baking or broiler failing to ignite/reach programmed temperature
Viking Dishwasher — Error Codes
| Code | What it means | Urgency |
|---|---|---|
| F1 / E15 |
Water Leak Detected
Float switch or leak sensor activated by water in the bottom safety tray. Continuous drain pump activity is triggered to prevent room flooding.
|
High |
| E1 / I10 |
Water Fill Timeout
Dishwasher failed to reach required water level within the designated time frame. Check fill valve, water supply line, or float switch.
|
High |
| E2 / I20 |
Drain System Failure
Water failed to drain out of the tub. Caused by clogged triple-filter assembly, kinked drain hose, or jammed drain pump impeller.
|
High |
| E4 / I60 |
Heating Element Circuit Fault
Heating element open circuit, ground fault, or heater relay trip detected on control board. Water fails to heat properly.
|
Medium |
| E5 / I50 |
Wash Circulation Pump Fault
Wash motor seized, capacitor failed, or debris jammed in wash impeller. Water fills but spray arms do not rotate.
|
High |
| F3 |
Diverter Valve Error
Diverter motor failure or food debris blocking water distribution between upper and lower spray arms.
|
Medium |
Viking Professional dishwashers use high-pressure wash arms and fine filtration systems. Inspect and rinse the stainless steel mesh filter in the bottom sump every month to prevent drain pump seizures and E2/I20 blockage codes.
Signs your Viking dishwasher needs a professional
- Standing dirty water in the bottom tub after cycle completion
- Drain pump running continuously with door open or power button off
- Dishes coming out cold and wet with detergent pod un-dissolved
- Loud humming noise when wash cycle begins without spray arm rotation
Viking Repairs in the Field
A look at recent professional service and diagnostic work on Viking high-end ranges, cooktops, and double ovens.
Viking Repair FAQ
Why is my Viking appliance displaying an error code?
Viking luxury appliances are engineered with internal electronic monitoring boards. When temperature, pressure, or electrical components operate outside strict factory tolerances, a fault code is logged on the display.
Can I reset my Viking oven or refrigerator error code?
You can perform a hard reset by switching off the dedicated circuit breaker at your main breaker panel for 5 to 10 minutes. If the underlying hardware fault persists, the error code will return as soon as power is restored.
Why is my Viking range oven not heating even though the cooktop works?
Viking ranges use separate electrical circuits for ignition controls and heavy heating elements or gas igniter valves. A tripped thermal fuse, faulty RTD sensor (F02 code), or cooling fan failure (F03 code) will lock out oven heating while burner ignition continues to function.
Do you use genuine Viking OEM replacement parts?
Yes, all Viking repairs are performed using original factory OEM replacement components to preserve your unit's performance, safety certifications, and warranty specifications.
Still seeing the error?
Our technicians diagnose and repair Viking appliances every day. Get it fixed right the first time.